Hive Chemicals & Equipment

	Main Index Search Register Login Who's Online FAQ Links
	Main Index Search Register Login Who's Online FAQ Links

	1 Online, 0 Active		You are not logged in

This is a historical archiveThe forum is read-only. Private information has been removed. It is not possible to login.

	Chemicals & Equipment

All 4 posts Subject: diethlyether from starter fluid purity Please login to post Down

fnord
(Hive Bee)
10-09-04 15:53
No 535041
User Picture       diethlyether from starter fluid purity

how pure is the ether exracted with just water from starter fluid? does it matter if u use too much water or too little? how much heptane isnt extracted thanxd byby

blunts
(Newbee)
10-10-04 09:23
No 535169
      just tried it

I felt inclinded to add my 2 cents to this topic since swim just tried this a few days ago. While swim cant tell you the exact purity, swim found it very easy to see the 2 layers, and siphon off the ether layer. It has a very strong distinct smell similar to nail polish remover (acetone?) BTW, if you intend on huffing it...dont....its some gross shit

Jacked
(Ancient Alchemist Delux)
10-10-04 12:48
No 535183
      reply

Actually you should see three layers. There is an oil intended for top end lubrication when this stuff is applied.. The amount of water should be at least half in half and a vigorous shaking is necessary to dislodge this oil from the ether in which it is soluble.. If shaken hard and long enough you will see this oil in between the two major layer, Extract the ether quickly because if allowed to sit for any amount of time the oil will redissolve into the ether layer..

Tighten Up! (UH)

Jacked
(Ancient Alchemist Delux)
10-10-04 13:10
No 535186
      reply

Post 476132 (lugh: "Preparations", Newbee Forum) will give you a better route than the starting fluid extraction.

Tighten Up! (UH)

	https://the-hive.archive.erowid.org	the-hive@erowid.org



Powered by Electricity^TM Release 1.02.3, © 2017-2023, PR Newswire Services Co.
Links Erowid Rhodium

	All 4 posts		Subject: diethlyether from starter fluid purity		Please login to post		Down


		fnord (Hive Bee) 10-09-04 15:53 No 535041				diethlyether from starter fluid purity
						how pure is the ether exracted with just water from starter fluid? does it matter if u use too much water or too little? how much heptane isnt extracted thanxd byby



		blunts (Newbee) 10-10-04 09:23 No 535169				just tried it
						I felt inclinded to add my 2 cents to this topic since swim just tried this a few days ago. While swim cant tell you the exact purity, swim found it very easy to see the 2 layers, and siphon off the ether layer. It has a very strong distinct smell similar to nail polish remover (acetone?) BTW, if you intend on huffing it...dont....its some gross shit



		Jacked (Ancient Alchemist Delux) 10-10-04 12:48 No 535183				reply
						Actually you should see three layers. There is an oil intended for top end lubrication when this stuff is applied.. The amount of water should be at least half in half and a vigorous shaking is necessary to dislodge this oil from the ether in which it is soluble.. If shaken hard and long enough you will see this oil in between the two major layer, Extract the ether quickly because if allowed to sit for any amount of time the oil will redissolve into the ether layer.. Tighten Up! (UH)



		Jacked (Ancient Alchemist Delux) 10-10-04 13:10 No 535186				reply
						Post 476132 (lugh: "Preparations", Newbee Forum) will give you a better route than the starting fluid extraction. Tighten Up! (UH)

All 4 posts	End of thread	Top